Categories
Online Marketing

What Is a Culvert?

I ’ m, not talking about arguments in the office. I mean conflicts when two or more things need to be in the same place. There are a lot of challenges in getting facilities. Over under around or between each other and there ’ s a specific structure: ubiquitous In the constructed environment that ’ s, sole purpose is to deal with the conflict between Roadways and streams, canals and ditches Hey.

I ’ m Grady, and this is Practical Engineering On today. ’ s episode. We ’ re! Talking about! Culverts This article is sponsored by NordVPN More on that later, Culverts are one of those things that seem So obvious that you never take the time to even consider them, They ’ re, also so common that they practically Blend into the background, But without them life in this world would Be quite a bit more complicated.

Let me explain what I mean. Imagine you, ’ re designing a brand new roadway To connect point A to point B, It would be nice if the landscape between these points, Was perfectly flat with no obstructions or topographic relief, But that ’ s rarely true More likely on the way you ’ ll encounter. Hills and valleys structures and streams, and you ’ ll – have to decide how to deal with Each one Your road can go around some obstacles, but For the most part, you ’ ll have to work with what you ’ ve got.

A roadway has to have gentle curves, both horizontally And vertically so you might have to take soil or rock from the high spots and build Up the low spots along the way also called cut and fill, But you ’ ve got to be careful about filling In low spots, because that ’ s where water flows, Sometimes it ’ s obvious, like rivers or perennial Streams, but lots of watercourses are ephemeral, meaning they only flow when it rains.

If you fill across any low area in the natural Landscape, you run the risk of creating an impoundment. If water can ’ t get through your embankment It ’ s going to flow over the top. Not only can this lead to damage of the roadway It can be extremely dangerous to motorists and other vehicles. One obvious solution to this obvious problem: Is a bridge the classic way to drive a vehicle over a body of water, But bridges are expensive.

You have to hire a structural engineer, install Supports girders and road decks: It ’ s, just not feasible for most small creeks And ditches So instead we do fill the low spots in, but We include a pipe, so the water can get through That pipe is called a culvert and there ’ s. Actually, quite a bit of engineering behind this innocuous bit of infrastructure, I know what you ’ re, thinking, “, Just a pipe Under a road, How complicated could it be ”? Well, allow me to introduce you to the U.

S Federal Highway Administration; ’ s Hydraulic Design of Highway Culverts! Third edition! Yes, you ’ re! Seeing that right, 323 pages Of wonderful guidelines on how to get water to flow under a road But worry not because I have taken my favorite Parts of this manual and built a demonstration, so you can appreciate the modern marvel that Is the highway culvert as much as any red-blooded civil engineer? A culvert really only has two jobs.

It has To be able to hold up the weight of the traffic passing over without collapsing, and it has To be able to let enough water pass through without overtopping the roadway, Both jobs are pretty complicated, but it ’ s. The second one I want to talk about in this article And it turns out that figuring out how much Water can pass through a culvert before the roadway. Overtops is a pretty complicated question.

In fact, there are eight factors that can Influence the hydraulics of a culvert (, 1 ) Headwater, or the depth of flow upstream of The culvert ( 2 ) The cross-sectional area of the culvert barrel, ( 3 ), the cross-sectional Shape of the culvert barrel, ( 4 ), the configuration of the culvert inlet ( 5 ), the roughness of The culvert barrel, ( 6 ) the length of the culvert ( 7 ), the slope of the culvert and ( 8 ), the tailwater or depth of flow downstream.

We don ’ t have time to demonstrate how all These parameters affect the culvert flow, but the Federal Highway Administration actually Has a pretty comprehensive article on YouTube ( with a much nicer flume than mine )? If you Want to see more, One thing I do want to show is the two primary Flow regimes for culverts, which are outlet, control and inlet control, And these are pretty much exactly what they Sound like Outlet control happens when water can flow.

Into the culvert faster than it can flow out, That means flow is limited by either the roughness And friction in the culvert barrel or the tailwater depth at the outlet. It ’ s kind of hard to see the movement of Water here, so I ’ m: blowing some bubbles Notice how the culvert barrel is flowing full The entire area of the barrel is being taken. Advantage of for flow In outlet control flow conditions downstream Of the culvert can affect the flow rate, For example, if a tree falls across a ditch.

Downstream that can back up water, reducing flow through the culvert and causing the roadway To overtop Inlet control happens when the culvert inlet Is constricting the flow more than any of those other factors, Everything that affects the amount of water Passing below the road is happening at the inlet. That means changing the roughness of the inside Of the barrel or anything downstream won, ’ t change.

How much flow makes it through It. ’ s easy to show this in my model because You can see inside the culvert barrel, You can tell that the flow depth in the culvert Is shallow and the full flow area of the barrel is not being taken advantage of? There are a wide variety of configurations. That the inlet to a culvert can have, If you pay attention, you ’ ll, see all kinds. Of culvert inlets, Some common types include projecting where The pipe protrudes from the embankment mitered, where the pipe is cut flush to the embankment And headwall, where the culvert begins at a vertical concrete wall, sometimes accompanied By concrete wing walls to further direct flow into the barrel, Unsurprisingly, each of the multitude of different Inlet configurations has a different effect on the culvert hydraulics In my demo.

I can do a test of two of these Inlet configurations to show the difference. First, I ’ m testing the projecting inlet. This is one of the least efficient configurations. Because there ’ s, nothing to help train the flow into the culvert. You can see that the headwater elevation is Quite high even close to overtopping the headwall in my flume, And even with all that pressure upstream There, ’ s not that much water coming through the culvert; It ’ s, only flowing about half full.

I ’ ll mark the water level with googly eyes. Next, I reconfigured the demo to make the culvert Flush with the headwall – And I also rounded over the inside edge of The pipe giving the flow a smoother entrance – I didn – ’ t change how much flow the pump is. Creating but you can see that the headwater is much much lower. That means the inlet is more efficient because It takes less driving headwater to get the same amount of flow through the barrel.

In fact, as I cranked up the flowrate higher And higher, I realized that even with as much headwater as I could create, this configuration Was still acting as an outlet-controlled culvert, The smooth and flush inlet was allowing as Much flow as possible through, Of course, there are really elaborate. Culvert Inlets that can be extremely efficient, but, like all infrastructure, culvert design is An exercise in balancing cost with other factors.

You can spend a lot of money on a fancy. Culvert Inlet that has perfectly smooth edges to guide the water gently into the barrel, or you could Just bump up to the next pipe size, Calculating flow through a culvert can be Quite complicated because culverts can transition between inlet and outlet control depending On flow rate, And even within these two major flow regimes, Of inlet and outlet control, there are a whole host of subregimes, each of which has its Own hydraulic equations, Of course we have software now, but back in The 1960s and 70s the Federal Highway Administration came up with a whole group of these cool nomographs To simplify the hydraulic design of culverts, The way this works is you first find the right Chart for your situation, [ 7A ].

This one is a culvert with a submerged outlet. Flowing full Each one is a little different, but in this One you draw a line connecting the culvert length to its diameter, Then draw a line connecting the headwater Depth to the intersection of your other line, with the turning line Extend this line to the discharge scale to Find out the flow rate passing through the culvert, I love little tricks like this.

That boil down All that hydraulic complexity into a quick calculation, you can do with a straightedge In less than a minute, Next time you ’ re, driving or walking along A street keep an eye out for culverts And if it ’ s, raining take a look at the Flow See if you can identify whether the culvert Is outlet or inlet controlled and be thankful that we have this ordinary but remarkable? Bit of infrastructure to let you safely walk or drive right over.

A lot of us are working from home. These days. And if you ’ re like me, your job requires you to connect to the company network through A VPN, The IT department – doesn, ’ t trust that I ’ ve. Set a secure password on my home router that I ’ ve updated the firmware on my printer Or that I ’ m, aware of let alone have fixed any number of other vulnerabilities on my Personal network And honestly, if the IT department, doesn, ’ t Trust me, I don ’ t trust me either That ’ s why I use NordVPN These days.

Most major websites are already Encrypting traffic and many smartphones do the same, But there are people and organizations constantly Working to find new vulnerabilities that take advantage of people online, NordVPN, encrypts and tunnels, my web traffic Making it much harder for anyone who would have or could have been a part of that chain, From seeing my information, I don ’ t have to worry if I ’ m, on a secure Network and I don ’ t have to trust my ISP to be a good steward of my data.

I just click connect and it ’ s done. It works on all my devices and there ’ s. No Limit on bandwidth, I lock the doors to my house when I ’ m away. And I turn on NordVPN when I ’ m using my computer, Not because I think it ’ s likely someone Is going to take advantage of me, but because it takes no effort at all to do so and and It reduces my vulnerability if they ever tried. If that philosophy makes sense to you, they ’ re.

Offering a awesome discount Go to https //NordVPN.Com/practicalengineering Or use code PRACTICALENGINEERING to get 70 % off a 3 year plan plus 1 additional month. Free That ’ s, NordVPN.Com/practicalengineering Or just click the link in the description. Thank you for reading and let me know what You think


Videos are truly an awesome way to get the point across. Any type of content from your business is important!

 

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.